Installation and acceptance of toilet for decorati

2022-07-22
  • Detail

Every family needs to use the toilet. As it is related to the circulation of sewage, poor installation of the toilet will lead to water leakage and peculiar smell at home. Therefore, attention must be paid to the installation of toilets. What are the steps of toilet installation, what should we pay attention to, and what should we keep in mind in this step

the meaning of installing the toilet

every family should use the toilet. Because it is related to the circulation of sewage and dirt, poor installation of the toilet will lead to water leakage and peculiar smell at home. Therefore, attention must be paid to the installation of toilets. What are the steps of toilet installation, what should we pay attention to, and what should we keep in mind in this step

installation process of toilet

toilet installation is relatively easy. Generally, after buying it back, install it by yourself or ask a worker to install it. Although the toilet installation is simple, it is very important to master the installation method of the toilet. Only when the toilet is installed accurately can people feel relieved to use it. Let's take a look at the general process of toilet installation

1. Check the levelness between the sewage pipe and the ground

before installing the toilet, comprehensively check the sewage pipe to see whether there is mud, sand, waste paper and other debris blocking in the pipe. At the same time, check whether the ground of the toilet installation position is horizontal in the front, back, left and right. If the ground is uneven, level the ground during installation

2. Determine the center of the drain pipe

turn the toilet over, determine the center on the toilet drain outlet, and draw a cross center line, which should extend to the feet around the bottom of the toilet

3. Fix the toilet

align the cross line on the toilet with the floor drain outlet, install the toilet horizontally, press the seal ring tightly, and install the ground screw and decorative cap

4. Do a good job of bottom sealing

install a special sealing ring on the toilet drain outlet, or apply a circle of glass glue (putty) or cement mortar around, and the ratio of cement to sand is 1:3

5. Install water tank accessories

flush the pipe with water for 3-5 minutes to ensure the cleanness of the water pipe; Then install the angle valve and connecting hose, and then connect the hose with the installed water inlet valve of the water tank fitting and connect the water source according to the

6. Commissioning inspection

check whether the water inlet and sealing of the water inlet valve are normal, check whether the installation position of the drainage valve is flexible, whether there is blockage and leakage, and whether there is missing installation of the filter device of the water inlet valve

precautions for installing the toilet

1. Before installation, the master should first conduct a comprehensive inspection of the sewage pipe to see whether there are debris such as mud and sand, waste paper and so on blocked in the pipe, and at the same time, check whether the floor of the toilet installation position is horizontal before, after, left and right. If the floor is found to be uneven, the floor should be leveled when installing the toilet. Cut the water outlet short and make it 2mm-5mm higher than the ground as far as possible if conditions permit

2. The water outlet shall be handled smoothly by the installer. The outlet of the bottom of the toilet shall be equipped with a special flange for the toilet, or coated with glass glue to align with the water outlet evenly. The bottom and surrounding of the toilet shall be glued, and the gap between the toilet and the wall shall be even, placed properly and stably

3. After the toilet is in place, it is required to have no leakage, the water level is correct, the flushing is smooth, the switch is flexible, and the cover is stable

4. Generally, foundation screws are not added when installing the toilet, but the reserved holes on the toilet should be blocked with glass glue to prevent odor

5. If foundation screws are installed, first use the special sealant installed in the toilet, and apply it evenly at 2cm on the periphery of the drainage outlet of the toilet base. The drainage outlet of the toilet should be facing the central position of the drainage pipe. Draw the position of the expansion bolts on the left and right sides of the toilet, remove the toilet, drill holes, and bury the expansion bolts. Pay attention to that the newly perforated expansion bolts are embedded in the hole, which may break the waterproof layer. It is suggested that while embedding the expansion screws, Fill the sealant around the hole, and then bury the expansion bolt. First screw the expansion bolt, let the expansion bolt completely release, strengthen its tension, then screw off the upper screw, put the toilet, and then screw the screw directly and cover the cap to maintain the overall appearance of the place. At the intersection of the toilet and the periphery of the ground surface, because the toilet is not integrated with the ground surface, you can use the jointing agent

6 and transparent sealant to stir, seal the outer opening of the toilet to maintain its integrity with the ground surface, and also block the local toilet water on the periphery of the toilet

7. After the toilet is installed, the water can be used only after the glass glue (putty) or cement mortar is cured. The curing time is generally 24 hours. If an unprofessional person is invited to install it, usually in order to save trouble, the construction personnel will directly use cement as adhesive, which must not work. It fills the fixed position of the lower opening of the toilet. In fact, there is a drawback in the middle. The cement itself has expansibility, and over time, this method may lead to the cracking of the toilet base, which is not convenient for maintenance

8. Install or commission water tank accessories. Check the tap water pipe first, and flush the pipe with water for 3-5 minutes to ensure the cleanness of the tap water pipe; Then install the angle valve and the connecting hose, and then connect the hose with the installed water inlet valve of the water tank fitting and connect the water source according to the pressure, check whether the water inlet and sealing of the water inlet valve are normal, check whether the installation position of the drainage valve is flexible, whether there is blockage and leakage, and check whether there is a missing filter device of the water inlet valve

acceptance of toilet installation

1. Open the angle valve to check whether there is leakage at the connection port

2. Check whether the automatic valve in the box can be opened and closed flexibly

3. Check the distance between the water level and the overflow pipe after the tank is filled with water

4. Press both sides of the toilet with both hands and shake slightly to observe whether it is stable

5. Put a mass of toilet paper in the toilet, open the water hole of the board to flush and observe, and check whether there is leakage at each interface. Continuous flushing and placing shall not be less than three times. If the discharge is smooth and there is no leakage at each interface, it is qualified

what owners need to pay attention to in this step

1. Before choosing the toilet, first determine the size of your toilet, that is, how far is the water outlet from the wall? (the standard is only 300 mm and 400 mm)

2. Then choose your favorite style according to the size. Pay attention to the water-saving type (3-6 liters). When ordering, you should see the model and origin clearly. Now the products are mixed, and it is a regretless choice to shop around

3. Before installing the toilet, first determine whether the product you choose, and whether the accessories and instructions are complete. Look carefully at the instructions to understand some product matters, so as to prevent stealing beams and columns and cutting corners. Remember

郑州精神医院

南京男科医院

贵阳癫痫医院

武汉癫痫医院

Copyright © 2011 JIN SHI